• stebo@lemmy.dbzer0.com
    link
    fedilink
    arrow-up
    27
    arrow-down
    1
    ·
    9 months ago

    As a kid it took me a long time to understand what turning right even meant, because when the top goes right, the bottom goes left and the sides go up and down. It doesn’t make sense.

    • rekabis@lemmy.ca
      link
      fedilink
      arrow-up
      13
      ·
      edit-2
      9 months ago

      Even in my sixth decade, I beat people about the head with this, becoming the pedant from hell until they finally revert to clockwise and counterclockwise. And if they become specific enough to be “right over the top”, I go, “well, why not just say clockwise and avoid all that ambiguity?”

      Being on the spectrum, it took me into my very early teens to even figure out right from left. I was two grades ahead of my peers in math, and could read a map and navigate better than most adults, but I needed a high degree of specificity when it came to physical directions. Any assumptions that were inconsequential to others became massive roadblocks to me due to the innate ambiguity of assumptions.

      • stebo@lemmy.dbzer0.com
        link
        fedilink
        arrow-up
        10
        ·
        9 months ago

        I think the issue is that the words “clockwise” and especially “counterclockwise” are way too long and therefore people prefer saying “left” or “right”.

        • pixelscript@lemmy.ml
          link
          fedilink
          English
          arrow-up
          7
          ·
          9 months ago

          Not to mention a rapidly growing segment of the population is unable to read analog 12 hour clocks, so the analogy is not that helpful.

      • rmuk@feddit.uk
        link
        fedilink
        English
        arrow-up
        2
        ·
        9 months ago

        Okay, so, yeah. “Righty tighty” never worked for me but you know what did? Turning Clockwise would eventually make the screwhead block up against the wood. “Clockwise, blockwise”.

      • themusicman@lemmy.world
        link
        fedilink
        arrow-up
        2
        ·
        9 months ago

        “But it’s going anticlockwise if you look at it from behind…”

        If you mount a clock on the ceiling, which way do the hands go? What about their shadow on the floor?

        • pixelscript@lemmy.ml
          link
          fedilink
          English
          arrow-up
          3
          ·
          9 months ago

          Those are some really theoretical ways to observe a clock face.

          How about we just start saying, “torque in, torque out”? When the torque vector points in, the screw goes in (tightening). When it points out, the screw comes out (loosening). As long as you are standing on the side of the screw you can actually work with while working with it (and why wouldn’t you be?) this is never ambiguous.

          Of course, now we’re kicking the can down the road and relying on people wrapping their heads around the right hand rule… Hmm…

            • pixelscript@lemmy.ml
              link
              fedilink
              English
              arrow-up
              1
              ·
              9 months ago

              I have lived in a home with a ceiling fan for nearly 30 years and I cannot confidently answer this question off the top of my head.

              Maybe that’s just tremendous skill issue on my part, but recognizing that all ceiling fans are standardized to spin only one way and knowing which way that is seems like a weird thing to ask of someone who also needs a mnemonic for which way to tighten screws.

              • themusicman@lemmy.world
                link
                fedilink
                arrow-up
                1
                ·
                9 months ago

                That’s not what I meant. If you have a ceiling fan in front of you, how would you describe its rotation? Would it rotate the same way as its shadow? Or opposite? Why?

    • Ejh3k@lemmy.world
      link
      fedilink
      English
      arrow-up
      6
      ·
      9 months ago

      I’ve been wrenching on cars nearly 30 years. I’ve had mechanical maintenance as part of my actual job for a decade now. Two years ago it all finally clicked for me. Clockwise tight, counterclockwise loose.

    • hyves@feddit.nl
      link
      fedilink
      arrow-up
      3
      ·
      9 months ago

      In Dutch we only talk about turning screws clockwise and counterclockwise